Asphalt Repair, Wall Coatings, Joint Sealants, Crack Repair & Non-Slip Products
A complete flooring system depends on more than just the coating on the floor. Cracks need to be treated before they spread. Joints need to be filled and protected. Walls need protection in harsh environments. And every surface needs the right level of slip resistance. Elite Crete Hudson Valley in Wappingers Falls, NY carries the specialty products that handle all of it. Call us today at (845) 273-3494 to find the right product for your project.
Asphalt Repair Coatings
Asphalt and concrete surfaces in parking lots, parking garages, and exterior areas take constant abuse from traffic, moisture, and chemical exposure. Our asphalt repair coating product provides heavy-duty protection and waterproofing for these surfaces.
E100-PC2 Coal Tar Epoxy
E100-PC2 is a two-component coal tar epoxy coating designed for heavy-duty waterproofing and protection of asphalt and concrete surfaces. It is widely used in parking garages, parking lots, and other exterior surfaces where long-term waterproofing and resistance to water, de-icing salts, and petrochemicals are required. Coal tar epoxy is one of the most durable and cost-effective solutions for protecting horizontal concrete and asphalt in harsh outdoor environments.
Key uses include parking garage decks and ramps, exterior concrete and asphalt surfaces, bridge decks and other exposed structural surfaces, and anywhere long-term waterproofing protection is needed.
Ceramic Wall Coatings
Floors get most of the attention, but walls in industrial, food service, and wet environments need protection too. Our HERMETIC CVP Ceramic Wall Coating is a fluid-applied, seamless wall system engineered for environments where hygiene, chemical resistance, and durability on vertical surfaces are required.
HERMETIC CVP Ceramic Wall Coating
HERMETIC CVP is a ceramic-reinforced, fluid-applied wall coating system available in Neat and Flake finishes. It is applied directly to masonry, concrete block, drywall, and other vertical substrates to create a seamless, non-porous, washable wall surface. HERMETIC CVP is used in commercial kitchens, food processing areas, locker rooms, restrooms, breweries, veterinary facilities, and any environment where the walls need the same level of protection as the floor.
Key Advantages of HERMETIC CVP
- Seamless, non-porous surface with no grout lines to harbor bacteria
- Chemical resistant and easy to clean
- Available in Neat and Flake finishes for aesthetic flexibility
- Applied to block, masonry, drywall, and concrete
- Suitable for food service, healthcare, industrial, and wet environments
- Matches the look and performance of HERMETIC floor systems
- Creates a complete, hygienic floor-to-wall coating system
JFS-450H High Performance Adhesive Sealant
JFS-450H is a high-performance, flexible adhesive sealant used to seal joints, cracks, and transitions in resinous and cementitious floor systems. It provides a durable, chemical-resistant seal at floor joints, wall-to-floor transitions, and around drains and penetrations. It is suitable for interior and exterior applications in commercial and industrial environments.
JFS-680P GRID-LOCK Joint Filler
JFS-680P GRID-LOCK is a semi-rigid, polyurea joint filler designed for saw cut and construction joints in concrete floor systems. It fills and supports the edges of joints to prevent chipping and cracking under wheeled traffic and heavy loads. GRID-LOCK is the right choice for warehouse floors, manufacturing areas, and any environment where forklift or pallet jack traffic crosses control joints.
MERCAP-445 Crack Treatment & Injection Epoxy
MERCAP-445 is an epoxy crack treatment and injection product used to stabilize and fill cracks in concrete prior to the application of resinous or cementitious overlay systems. It bonds to both sides of the crack to create a controlled, stable surface that the overlay system can bond to. It is safe, non-hazardous, and designed to provide the correct level of flexibility and tensile strength for crack treatment applications.
QUICK-CRACK Crack Filler
QUICK-CRACK is a fast-setting crack filler used to prepare cracks in concrete for polymer modified cementitious overlay applications. It fills surface cracks quickly to create a more uniform surface before the overlay is applied. QUICK-CRACK is not a guaranteed structural crack repair but is an effective approach to controlling surface cracks under decorative overlay systems.
EC-1710 Oil Tolerant Epoxy Primer
EC-1710 is an oil-tolerant epoxy primer designed for use on concrete substrates that are contaminated with oil, grease, or other petroleum-based products. Standard epoxy primers require clean, dry concrete for proper adhesion. EC-1710 is engineered to bond even when residual contamination is present, making it the right primer for auto service bays, machine shops, and other areas where complete oil removal is difficult.
BACK-TRACK 60S Anti-Slip Additive
BACK-TRACK 60S is a non-slip aggregate additive that is broadcast into or mixed into coating systems to increase surface friction and meet slip resistance requirements. It can be added to topcoats, sealers, and overlay finishes to achieve the required coefficient of friction for ADA, OSHA, and NFPA compliance. BACK-TRACK 60S is used in any area where slip resistance is a safety priority, including ramps, stairways, wet areas, and exterior surfaces.
Key Advantages of Specialty Products
- Joint fillers protect concrete edges from chipping under wheeled traffic
- Flexible sealants accommodate movement at joints and transitions
- Crack treatments stabilize substrates before overlay or coating
- Oil-tolerant primer enables coating on contaminated concrete
- Non-slip additive meets ADA, OSHA, and NFPA slip resistance requirements
- Products work across resinous, cementitious, and mixed floor systems
- Essential preparation products for long-lasting floor system performance
Joint Sealants, Crack Repair, Non-Slip Additives & Specialty Products
This category covers the essential supporting products that make every floor system complete. From joint fillers that protect floor edges to crack treatments that stabilize the substrate before coating, these products do the critical prep and finishing work that most contractors need on every job.
JFS-450H High Performance Adhesive Sealant
JFS-450H is a high-performance, flexible adhesive sealant used to seal joints, cracks, and transitions in resinous and cementitious floor systems. It provides a durable, chemical-resistant seal at floor joints, wall-to-floor transitions, and around drains and penetrations. It is suitable for interior and exterior applications in commercial and industrial environments.
JFS-680P GRID-LOCK Joint Filler
JFS-680P GRID-LOCK is a semi-rigid, polyurea joint filler designed for saw cut and construction joints in concrete floor systems. It fills and supports the edges of joints to prevent chipping and cracking under wheeled traffic and heavy loads. GRID-LOCK is the right choice for warehouse floors, manufacturing areas, and any environment where forklift or pallet jack traffic crosses control joints.
MERCAP-445 Crack Treatment & Injection Epoxy
MERCAP-445 is an epoxy crack treatment and injection product used to stabilize and fill cracks in concrete prior to the application of resinous or cementitious overlay systems. It bonds to both sides of the crack to create a controlled, stable surface that the overlay system can bond to. It is safe, non-hazardous, and designed to provide the correct level of flexibility and tensile strength for crack treatment applications.
QUICK-CRACK Crack Filler
QUICK-CRACK is a fast-setting crack filler used to prepare cracks in concrete for polymer modified cementitious overlay applications. It fills surface cracks quickly to create a more uniform surface before the overlay is applied. QUICK-CRACK is not a guaranteed structural crack repair but is an effective approach to controlling surface cracks under decorative overlay systems.
EC-1710 Oil Tolerant Epoxy Primer
EC-1710 is an oil-tolerant epoxy primer designed for use on concrete substrates that are contaminated with oil, grease, or other petroleum-based products. Standard epoxy primers require clean, dry concrete for proper adhesion. EC-1710 is engineered to bond even when residual contamination is present, making it the right primer for auto service bays, machine shops, and other areas where complete oil removal is difficult.
BACK-TRACK 60S Anti-Slip Additive
BACK-TRACK 60S is a non-slip aggregate additive that is broadcast into or mixed into coating systems to increase surface friction and meet slip resistance requirements. It can be added to topcoats, sealers, and overlay finishes to achieve the required coefficient of friction for ADA, OSHA, and NFPA compliance. BACK-TRACK 60S is used in any area where slip resistance is a safety priority, including ramps, stairways, wet areas, and exterior surfaces.
Key Advantages of Specialty Products
- Joint fillers protect concrete edges from chipping under wheeled traffic
- Flexible sealants accommodate movement at joints and transitions
- Crack treatments stabilize substrates before overlay or coating
- Oil-tolerant primer enables coating on contaminated concrete
- Non-slip additive meets ADA, OSHA, and NFPA slip resistance requirements
- Products work across resinous, cementitious, and mixed floor systems
- Essential preparation products for long-lasting floor system performance
Frequently Asked Questions About Repair, Joint & Specialty Products
Do control joints need to be filled before applying a floor coating?
Yes. Control joints should be filled with a semi-rigid joint filler like JFS-680P GRID-LOCK before a resinous coating is applied. This protects the joint edges from chipping under wheeled traffic and prevents the coating from cracking at the joint line.
Can cracks be coated over without treatment?
Cracks should be treated before any coating or overlay is applied. Untreated cracks will telegraph through the finished surface and can grow over time. MERCAP-445 or QUICK-CRACK should be used depending on the type of overlay being applied.
What is coal tar epoxy used for?
Coal tar epoxy like E100-PC2 is used for heavy-duty waterproofing of concrete and asphalt surfaces, particularly in parking garages, parking lots, and exterior structures exposed to water, salt, and petrochemicals.
Can HERMETIC CVP wall coating be applied over block or drywall?
Yes. HERMETIC CVP applies directly over masonry, concrete block, drywall, and other vertical substrates. It creates a seamless, non-porous wall surface that matches the performance of HERMETIC floor systems.
How is BACK-TRACK 60S applied?
BACK-TRACK 60S can be broadcast onto a wet topcoat or mixed directly into a sealer or coating before application. The method depends on the system and the level of slip resistance needed. Our team can advise on the right application approach for your specific project.
Get the Right Specialty Products for Your Project
The supporting products are just as important as the coating itself. Elite Crete Hudson Valley supplies asphalt repair coatings, wall coatings, joint sealants, crack treatments, and non-slip additives for contractors across Westchester, Orange, Dutchess, and Putnam counties in New York. Call us today at (845) 273-3494 and let our team help you find the right product for your next project.